The trailed HIRL mixer wagon T Vertikal L with one auger comes with a capacity from 9 till 13 m³.

HIRL trailed mixer-wagon T Vertikal L - with one auger

The trailed HIRL mixer wagon T Vertikal L with one auger comes with a capacity from 9 till 13 m³. The following types are available:

  • Mixer wagon T 900 VL
  • Mixer wagon T 1100 VL
  • Mixer wagon T 1300 VL
The trailed HIRL mixer wagon T Vertikal L with one auger comes with a capacity from 9 till 13 m³.

Quality - Made in Germany

The rigid mixing-tank is completely made out of S355 steel. For the tank floor 20 mm thick steel is used, the side walls are 8 mm thick and a conical tank cover ring stiffens the tank additionally.

HIRL T 1300 VL with chain conveyor at the front

HIRL T 1300 VL (with chain conveyor at the front)

Also the massive, 15 mm thick auger made out of S355 steel with at least 2.5 windings upwards and a Hardox cutter edge at the beginning of the auger are made to last. An upright final blade at the end of the spiral and saw tooth blades on the auger ensure a complete and effective dissolving of the silage-bales.

HIRL T 900 VL with chain conveyor at the back

HIRL T 900 VL (with chain conveyor at the back)

This trailed vertical-auger mixer wagon is fully equipped with a chain conveyor using V2A Stainless steel bars. A generous dimensioned suspension with dual mounted tyre assemblies carries the 9 m³ mixer wagon effortless.

Hirl Diet Feeder T Vertikal L: On request also available in minimal configuration.

If requested, the mixing wagon is available with minimal specifications:

  • Machine without 2 speed gear box
  • Machine without conveyor (with direct discharge on left and right side)
HIRL T 900 VL (with 2 direct discharges)

HIRL T 900 VL (with 2 direct discharges)

This Model of the T Vertikal series requires very low input power. The one-auger vertical mixer has 2 direct discharges and is ideal as a cost effective entry-solution, with which you can achieve a very precise mixing of the fodder without spending lots of money.

Rugged, efficient and built to last!

The HIRL mixer-wagon T Vertikal L is with a tank of 9 till 13 m³ capacity, extensive standard equipment and lots of different additional equipment possibilities a cost effective, but very performant entrance in the mixer-wagon line-up of HIRL-Technik. We would be very pleased if we could meet to an appointment to discuss the best suited configurations for your needs.

The vertical mixer-wagon HIRL T Vertikal L - standard equipment

  • Mixing-tank with a conical tank cover ring made out of S355 steel
  • Optional with intermediate-flange making capacity-upgrades afterwards possible
  • Tank Base plate 20 mm thick
  • Side panels 8 mm thick
  • Mixing auger 15 mm strong made out of S355 steel
  • Auger equipped with cutting blades
  • Two mechanic counter blades
  • Planetary reducing gear with a ratio of Ieff = 18.3
  • Two gear transmission
  • Height adjustable drawbar, can be mounted in low and high position
  • Norm flange on drawbar (As standard with drawbar eye, optional Scharmüller K80 available)
  • Tyres 355/60 R 18 MPT new
  • Robust frame with double steel tubing
  • 4 mounting points for weighing bars
  • Discharge at front with chain conveyor or optionally with two direct discharges
  • Ascension ladder with overview-platform
  • Support foot with mechanical fast locking mechanism
  • Bowden cable remote control with 3.0 m long cable, mounting plate with two powerful magnets
  • Extern oil supply from the tractor necessary (1 x one way control unit with return flow)
  • Zone-hardened blades
Solid planetary transmission for up to 30 000 Nm torque output

Solid planetary transmission

  • maximum 30 000 Nm output-torque
  • Auger-bearing on the upper side with lubrication tube
  • External oil reservoir
  • power take-off centralizer with one shaft output as standard
  • 1 3/4 inch in- and output power take of shaft
Special-spring-steel blades with wolfram-carbide coating on request

The following equipment is optionally available

  • Chain Conveyor discharge with bars made out of stainless steel at the rear (slider-display activated over Bowden-cable)
  • Left and right-sided discharge wit Chain Conveyor
  • Special-spring-steel blades with wolfram-carbide coating on request
  • Tandem axle
  • On-board hydraulics
  • Parking brake with hydraulic spring reservoirs (brake-pads 350 x 80 mm, one cylinder)
  • Two litre pneumatic braking system (brake-pads 350 x 80 mm - with wheel chocks and spherical brake (for TÜV-certification)
  • Hydraulical support foot (simple version, control unit on tractor necessary)
  • Three-chamber rear light complying with traffic regulations
  • TÜV - certification with operating licence for up to 25 km/h
The vertical mixing auger is available with 8 or 10 blades.

Auger in the mixer-wagon T Vertikal L

The vertical mixing auger is available with 8 or 10 blades. The Hardox cutter edge comes as standard.

The mixing process

The mixing process

Quick bale-dissolving with tractors powered by 65 HP or upwards

Easy to tow - for smaller tractors as well

Extra easy to tow

The optimal transmission gear reduction makes the mixer-wagon T Vertikal L fitting to your tractor

Optimized vertical auger: Models with 10 m³ upwards come with 2.5 spiral-windings or more

Optimized vertical auger

Models with 10 m³ upwards come with 2.5 spiral-windings or more

Programmable weighing computer PTM Graphic

PTM Graphic

Programmable weighing computer with:

  • 4 weighing bars lengthways mounted - 54 mm diameter
  • 15 recipes, 15 ingredients
  • Recipes and ingredients shown with name
  • Options of programming the overall weight or per cattle
  • consumption display
  • Big, illuminated display
  • Logical menu navigation
  • Optional with remote-control
Weighing computer PTM FC 20

PTM FC 20

Weighing computer with:

  • 4 weighing bars lengthways mounted - 54 mm diameter
  • Big, easy to read, red letters
  • Partial weight
  • Overall weight
  • Zero position through calibrating
Weighing computer PTM Graphic Memory, supports data-transfer to PCs

PTM Graphic Memory

Weighing unit for the data-transfer to PCs:

  • 4 weighing bars lengthways mounted - 54 mm diameter
  • 80 recipes, 20 ingredients
  • Data-transfer to PC possible
Power take-off drive shafts: Various different versions available

Power take-off drive shafts

  • Cardan shaft normal (Walterscheid type W2400)
  • Cardan shaft normal (Walterscheid type W2500)
  • Cardan shaft with one-sided wide angle (Walterscheid type W2400)
  • Cardan shaft with one-sided wide angle (Walterscheid type W2500)
  • Cardan shaft with both-sided wide angle (Walterscheid type W2400)
  • Cardan shaft with both-sided wide angle (Walterscheid type W2500)

Technical Spec - Weight and Dimensions

* depending on set of tyres

** deviating design on request realizable

*** depending on chosen equipment

Effective June 20th 2014. Technical changes reserved

Type Capacity Length Width Maximum height* ** Curb-weight*** Attachment-height of drawbar Discharge height* (of conveyor) Power take-off shaft Permissible towing capacity Load on drawbar